-
High Light
DC30V incremental decoder
,blind hole incremental decoder
,blind hole incremental encoders
-
Model SelectionBlind Hole Shaft/ Through Hole Shaft
-
TypeIncremental Type
-
ResolutionUp To 16384ppr
-
Output CircuitN, V, F, C, E
-
Output PhaseA, B, Z
-
ProtectionIP50
-
Place of OriginShanghai, China
-
Brand NameHENGXIANG
-
CertificationCE,ISO9001
-
Model NumberK38
-
Minimum Order Quantity1Pcs
-
PriceConsult us
-
Packaging Detailseach 1 piece was packed into single carton box
-
Delivery Time3-5 working days for sample order, 7-15 working days for mass order
-
Payment TermsL/C, D/A, D/P, T/T, Western Union, MoneyGram
-
Supply Ability100K pieces per year
ISO9001 Blind Hole Voltage DC30V Incremental Decoder Encoders
K38 shaft diameter blind hole Voltage DC5V-30Vincremental encoder & decoder
| Items | Basic parameters |
| Brand | HENGXIANG |
| Encoder type | Incremental encoder |
| External diameter | 38mm |
| Thickness | 38mm |
| Installation dimension | R23.5mm(spring plate 38T45) |
| Hollow shaft type | blind hole ; through hole |
| Hollow shaft diameter | 5mm,6mm,6.35mm;8mm |
| Resolution | 50;60;66;100;200;250;300;360;400;450;500;512;600;720; |
| 750;800;900;1000;1024;1200;2000;2048;2500;5000;8192;10000;16384 | |
| Output phase | Phase A,B,Z A- B- Z- |
| Supply voltage | DC5V ; DC8-30V |
| Outlettype | Cable out from side |
| Cable out from back | |
| Output mode | NPN/PNP(Open Collector Output) |
| Voltage output | |
| Push-pull output | |
| Long line drive (26LS31) | |
| Compatible RS422 | |
| Long line drive (RT7272) | |
| Environmental temperature | Operating temperature: -20~+90° (Non icing) |
| Storage temperature: -25~+100° (Non icing) | |
| Environmental humanity | Operating and storage: 35~85%RH (non-condensing) |
| Shell | Die cast aluminium |
| Consumption current | 100mA Max |
| Shaft Load | Radial: 40N; Axial:20N |
| Top REV | 5000RPM ;IP65≤3000r rpm |
| Insulation strength | AC500V 60s |
| Insulation resistance | 10MΩ |
| Mark to Space ratio | 45% to 55% |
| Top Resonse Frequency | 100kHz Max |
| Shell Material | Dia cast aluminium |
| Bearing life | 1.5x109 revs at rated load(100000hrs at 2500RPM) |
| GND | not connect to encoder |
| Shaft Material | Stainless steel |
| Vibration(endure) | Amplitude 0.75mm,5-55Hz,2 hours for X/Y/Z direction individually |
| Shock(endure) | 490m/s2,11 ms three times for X,Y,Z direction individually |
| Protection grade | IP50 ; IP65 |
| Cable length | 1000mm |
| starting torque | less than 9.8X10-3 N.m |
| Intertia moment | less than 6.5x 10-6kg.m2 |
| package | Carton box |
| Net weight | About 140g (with package) |
| Certification | CE |
Principle of encoder
An incremental rotary encoder outputs a certain amount of Pulses per Revolution. The higher this PPR number, the smaller the angle between each pulse. This PPR number is fixed for ordinary incremental encoders. Programmable incremental encoders can adjust this value to a desired number by a software change.
Today most incremental encoders have a Push-Pull (HTL) or RS422 (TTL) output driver, these have replaced most of the older output circuits like Open Collector NPN, Open Collector PNP, Voltage Output.
Push-Pull (HTL) circuits, also known as Totem Pole, provide a signal level which corresponds to the applied supply voltage. The supply voltage typically ranges from 8 to 30 VDC.
With proper connections you can use the Push Pull interface to replace true open collector circuits by using an external diode connected in a way to limit the direction of the current for RS422 (TTL) circuits provide a constant 5 V signal level that is not dependent on the supply voltage. Two supply voltage ranges can be selected: From 4.75 to 5.5 VDC (can be used to replace open collector output drivers) or from 8 to 30 VDC. Using differential signals the output fully complies to the RS422 standard.
Production date
1. for 1-10 samples: 3-5 working days
2. for 20-50 mass production: 7-10 working days
3. for over 100pcs, production will be discussed with customers and ship on time
Payment terms:
1. T/T, western union, credit card, Paypal, etc
2. 3-5 working days after payment received
3. Encoders will be shipped once ready
Shipment
Goods can shipped via TNT, FedEx, UPS, DHL, EMS, etc.
You could select the express according to your requirements if freight collector
If you do not have any courier account, we will check and find a cheapest and safety express for you.
Our factory has 30% discount with most courier company, so price could be as cheap as possible.
More information
If you are looking for more information about our factory or about our products, please contact us or email us right now, we will reply you as soon as possible.
Our products are sold all over the world, you can rest assured.